The input shaft diameters and keyways are the same, so existing couplings and drive shafts do not have to be replaced. All service ports are also easily accessible. Reduction ratios are within +/-2% of the Marley® reduction ratios, eliminating the need to make costly fan pitch adjustments.

Model	HORSEPOWER RATING
A20	20	25	30	35
A22						47	53	60	70
A27					40			60		75	80
A32												160
A34													180
A36														200	220	230	250
A38																	250

Ratio

All ratios are reducing and defined as the ratio of input speed to output speed. Single and double reduction ratios shown are exact within +/- 2%. Ratios shown in blue in each table are normally stocked and drives ordered with these ratios can be shipped within our normal lead time. Check with the factory for availability of all model ratios not shaded.

Ratings

AGMA and CTI recommend a minimum service factor of 2.0 for gear drives in cooling tower fan service when driven by electric motors or steam turbines. All ratings are service ratings and include a 2.0 service factor unless otherwise noted. Ratings are listed for 60 cycle electric motor speeds. Ratings for speeds less than 1750 rpm are proportional to the rating at 1750 rpm. Contact the factory for recommendations when the driver speed exceeds 1800 rpm.

Limited Warranty

The Amarillo Right Angle Gear Drive is guaranteed against defects in workmanship and material for a period of one year after installation when operated under normal service at rated capacity. Within the above stated period, the manufacturer will replace the defective parts returned transportation prepaid. The buyer shall not be entitled to incidental or consequential damages, losses or expenses. The guarantee will not apply to repairs made outside the factory without the consent of the manufacturer or to drives that have been subject to abuse, accident, neglect or improper installation. No warranty is made in regard to bearings, trade accessories, machinery, or other articles or merchandise not manufactured by us. This warranty is expressly made in lieu of any warranties otherwise expressed or implied by law.

Direction of Rotation

Normal rotation is both shafts clockwise as shown in the illustrations. Occasional use with both shafts rotating counterclockwise is permissible. Special bearing arrangements are used when the primary direction of rotation is counterclockwise and the gear drives should be ordered accordingly.

Rotational schemes with the shafts rotating in opposite directions are available on special order.

Straight Output Shaft Information

All AMARILLO "A" series right angle cooling tower drives may be furnished , upon request, with a cylindrical output shaft. The most common cylindrical shaft diameter is shown in the following table, however, other shaft diameters can be supplied within engineering limits. When requesting a cylindrical shaft the following information must be provided before an order can be accepted.

Model	Dia.	Model	Dia.
A20	2"	A32	4 1/2"
A22	2 5/8"	A34	5"
A27	3"	A36	5"
		A38	5"

Length of shaft (D)_________________ Keyway size (F)____________________

Shaft diameter (E)_________________ Overall height (C)___________________

Tapered Output Shaft Information

All AMARILLO "A" Series right angle cooling tower drives may be furnished, as standard, with the tapered output shaft shown in the drawing. On rare occasions the gear drive being replaced may have a different output shaft taper. Amarillo Gear Company will provide a matching shaft when the following information (or shaft drawing) is provided. This information is required before an order can be accepted.

Length of taper (D)________________ Keyway size (F)______________________

Small end diameter (E1)____________ Keyway parallel to centerline or taper_______

Large end diameter (E2)____________ Overall Height (C)_____________________

Weights and Shipping Dimensions

Model	Net Weight (lbs)	Weight With Export Boxing (lbs)	Export Box Dimensions (LxWxH) (in)
A20	200	240	29 x 19 x 27
A22	440	500	36 x 23 x 34
A27	840	940	36 x 40 x 30
A32	1560	1720	55 x 36 x 40
A34	1940	2190	58 x 46 x 40
A36	1960	2210	58 x 46 x 40
A38	1960	2210	58 x 46 x 40